*****************************   GP-Pro EX Ver.3.6   ****************************
                                                                    January 2014
                                                 Digital Electronics Corporation

Preface

Thank you for using GP-Pro EX.
GP-Pro EX is software to create logic programs and screen data for graphical 
operation touch panels.
The Windows environment ensures operability and high performance.
Please visit the Pro-face website (http://www.pro-face.com/) for the latest
information.

Table of Contents
(0) Version
(1) New Features List
 = V3.60.000 =====
 1-1 Support of New Models
 = V3.50.000 =====
 1-1 Support of New Models
 = V3.12.000 =====
 1-1 Support of New Models
 = V3.10.000 =====
 1-1 Support of New Models
(2) Limitations
 2-1 Editor
 2-2 Display Unit
 2-3 Device/PLC
 2-4 WinGP
(3) When Serial No. and License Key Code are not input
(4) Installation and Uninstallation
 4-1 Installation
 4-2 Uninstallation
(5) User Registration
(6) Manuals
(7) Fixed Defects
 = V3.60.000 =====
 7-1 Editor
 7-2 Display Unit
 7-3 Device/PLC
 7-4 WinGP
 = V3.50.000 =====
 7-1 Editor
 7-2 Display Unit
 7-3 WinGP
 = V3.12.000 =====
 7-1 Editor
 7-2 Display Unit
 7-3 Device/PLC
 = V3.10.000 =====
 7-1 Editor
 7-2 Display Unit
 7-3 Device/PLC
 7-4 WinGP

Contents
================================================================================
(0) Version
 Editor:         Ver.3.60.000
 System
  <GP-4200, GP-4300, GP-4400, GP-4500, GP-4600 series and LT4000 series>
   System:       Ver.3.60.0
   Sub-system:   Ver.3.60.0 (GP-4200, GP-4300, GP-4400, GP-4500, GP-4600 series.
                             Except for GP-4201TM and GP-4301TM)
                 Ver.1.2.0  (LT4000 series)
                 Ver.1.2.12 (GP-4201TM and GP-4301TM)
  <Other than above models>
   Runtime:      Ver.3.60.0
   OS Core:      Ver.1.1.1  (GP-4104)
                 Ver.1.3.3  (GP-4105, GP-4106 and GP-4107)
                 Ver.3.5.2  (ST3000 series and GP-3200 series)
                 Ver.3.6.1  (LT-3300 series)
                 Ver.3.5.1  (Other than above models)
 Memory Loader:  Ver.3.60.0 (LT4000 series)
                 Ver.3.10.0 (Other than above models)
 WinGP Runtime:  Ver.3.60.0

(1) New Features List
 = V3.60.000 ===================================================================
 1-1 Support of New Models
  <Supported Models>
   - The following two models are now supported:
     - LT-4000M (Rear Modular DIO)
     - LT-4000M (Rear Modular Analog)

  <Pro-face Remote HMI>
   - The LT4000 series now supports Pro-face Remote HMI.

  <Improvement in Editor Function>
   - In the preview, you can now change to the next and previous screens.
   - When moving objects, you can now define how many pixels to move
     with each keyboard cursor key.
   - GP-Pro EX now remembers the size of the Cross Reference dialog box.
   - Sampling settings are now easier to use.
   - You can now copy or change multiple screens in a single operation.
   - You can now copy objects in the Screen Data List and paste them
     onto the screen.
   - You can now split the Logic Screen.
   - You can now define the D-Script editor's background and text colors.
   - When entering messages in tables, GP-Pro EX now supports Autocomplete.
     The table also supports filters.

  <Others>
   - You can now control if a function block's local variable is
     shared or not.
   - EZ Numpad is now supported.
   - The following products can now run on Windows8.
     - GP-Pro EX (screen editor)
     - Transfer Tool
     - Version Reverter
     - Project Comparison Tool
     - Fingerprint Recognition Setting Tool
     - Project Converter
     - Recovery Tool
     - Pass-Through
     - WinGP
     - WinGP SDK
     - GP-Viewer EX
     - Camera-Viewer EX
     - Device Data Copy Tool

  <Communication Driver>
   - Newly-added communication driver
     - Crouzet  Millenium 3 FBD
     - Seiko Epson Corporation  Remote Ethernet
   - Function version upgraded communication driver
     - YASKAWA Electric Corporation  High Speed Ethernet Server
         DX200 series was supported
         FS100L series was supported
     - GE Intelligent Platforms  Series 90 Ethernet
         Allowable Number of Devices from 32 to 64 devices 
     - ODVA  EtherNet/IP Explicit Messaging
         Allowable Number of Devices from 16 to 64 devices 

 = V3.50.000 ===================================================================
 1-1 Support of New Models
   - The CANopen master driver is supported in the LT4000 series.

  <Pro-face Remote HMI>
   - The function in which a touch operation is limited to a server or 
     a client only is supported. 
   - The function in which "Synchronous" or "Asynchronous" can be selected for 
     connection mode is supported.
   - The number of special switches is increased in which operation is enabled 
     in the "Synchronous" or "Asynchronous" connection.

  <Communication Driver>
   - Newly-added communication driver
     - Beckhoff Automation GmbH TwinCAT ADS/AMS
     - CoDeSys Automation Alliance CoDeSys V3 Ethernet
     - Delta-TAU Data System Inc. PMAC Controller SIO
     - DENSO WAVE INCORPORATED b-CAP Protocol (TCP)
     - Saia-Burgess Controls Ltd. Saia Ether-S-Bus
   - Function version upgraded communication driver
     - GE Intelligent Platforms Series 90 Ethernet
        GP-4104 series is supported.
     - LS Industrial Systems XGT/XGB Series FEnet
        XGT (XGI, XGR) and XGB (XBM, XBC, XEC) series are supported. 
        The name of the driver is changed.
     - Mitsubishi Electric Corporation Q/QnA Series Ethernet
        The support address range is expanded.
     - Rockwell Automation EtherNet/IP
        The software version of RSLogix5000 which is to be supported in 
        the Import function of the L5K file is changed. 
        (Supported up to Ver. 20)
        Settings on the UI when directly connecting to the CompactLogix are 
        improved.
        The member of "Modules that generate controller tags or data type/
        structures on import" of the L5K import function is added.

= V3.12.000 ===================================================================
 1-1 Support of New Models
  <Supported Models>
   - The following four models are supported:
     - LT-4201TM (Modular Type DIO)
     - LT-4201TM (Modular Type Analog)
     - LT-4301TM (Modular Type DIO)
     - LT-4301TM (Modular Type Analog)

 = V3.10.000 ===================================================================
 1-1 Support of New Models
   - The setting to generate a touch sound is added when a touch is made while 
     an interlock is activated.
   - The function with which delay time of the switch can be specified 
     with a value of the address is added.
   - The function to change the state with the word value is added in Lamp.
   - The setting using the "msec" unit is added to the delay time in Switch.
   - The "Large" button is added for "System keyboard size".
   - The function with which Delay (Elapsed Time) can be checked is added 
     in Switch.
   - The system keypad can be displayed from Data Display on the window.
   - The system variable to be used for checking whether historical trend graph 
     is displaying the history data is added.
   - "Display Order" is added in Sampling Data Display.
   - The function which creates an index file of the backup data (bin file) 
     in sampling data in offline mode is added.
   - Two or more RPA Window Displays can be placed on one screen.
   - The function with which security settings can be edited in online mode 
     is added.
   - Russian (Cyrillic) standard font is added.
   - The function with which a system error history is displayed 
     in offline mode is added.
   - The function with which a MAC address is displayed in offline mode is 
     added.
   - The function with which SRAM backup data is not deleted at the time of 
     transfer is added.
   - Function Blocks (FB) which can make a logic program into an object 
     is supported.
   - System variables which allow users to confirm that transfer has been 
     executed are added.
   - EZ fingerprint recognition unit is supported.
   - EZ illumination switch is supported.

  <Pro-face Remote HMI>
   - Pro-face Remote HMI function is supported.

  <Function Support for GP-4201TM and GP-4301TM>
   - The function supported in GP-4000 series can be used in GP-4201TM and 
     GP-4301TM.

  <Improvement in Editor Function>
   - When Animation is used, icons are displayed in Screen List's workspace and 
     Screen Data List's workspace.
   - A mechanism in which font information on the parts using the text table 
     can be changed all at once is added.
   - "Display cross-hair cursor" can be set using the screen editor.
   - Comparison Tool is renovated so that parts attributes can be compared.
   - The icon indicating Screen Capture is always displayed on the toolbar to 
     make it easier to perform a screen capture in Preview.
   - Address color and part's ID to be displayed on the parts arranged on 
     the edit screen can be changed.
   - Alarm parts settings whose frequency in attribute change is high 
     are displayed in Basic Setting.
   - A link button is added so that a keypad screen can be easily edited from 
     Data Display.
   - Basic/Detail of the parts can be switched in Properties.
   - The icon is displayed in a complement list to be displayed when an address 
     is set.
   - When the setting registered in the text table is selected, 
     search refinement can be performed using an index number.
   - The registration button is added in the Switch/Lamp setting dialog so that 
     text can be easily registered in the text table.
   - When parts are arranged with "Snap to Grid" selected, the snap point can 
     be changed.
   - "Text Table" can be selected for "Search Type" in the Search window.
   - Alarm is added for the search object when "Text Table" is selected for 
     "Search Type" in the search option of the Search window.
   - Text table can be registered from Alarm.
   - Delimiter settings can be made when importing/exporting a CSV file and 
     a TXT file.
   - The setting to disable the size change is added when a cursor touches 
     the part while the part's position is changed using the keypad.
   - In the Switch/Lamp Settings dialog, the layout of the Label tab becomes 
     easier to see.
   - When call screen parts are selected, a center point is displayed.
   - "Input Mode" is added in Address View of Simulation so that "Compatible 
     Character Codes" and "Direct Text" can be switched.
   - When search is performed with the online monitor, the center of the logic 
     screen is focused.

  <Others>
   - EXE which can change a project created with V3.10 to the project of 
     V3.00 is created.
   - LT series can be changed to other series.
   - When "Mute" is set for the volume of a PC, the beep does not sound 
     at the time of starting WinGP/Simulation.
   - Windows7 64-bit is also supported.
     - PLC simulation
     - Pass-through
     - WinGP
     - GP-Viewer
     - Remote printer server
     - Camera-ViewerEX
     - Web-Server

  <Communication Driver>
   - GP-4000 series, GP-4000M series, GP-4100 series, LT-3000 series, and 
     USB/SIO (RS422/485) cables are additionally supported.
     For details on the supported communication drivers, refer to our website, 
     (http://www.pro-face.com/otasuke/).
   - Newly-added communication driver 
     - LSIS Co., Ltd. GLOFA series Cnet
     - Yaskawa Electric Corporation High-speed Ethernet server
   - Function version upgraded communication driver
     - Azbil Corporation Controller (CPL) 
       PBC, CMS, CMF, CMQ-V, MPC, MVF, CML, AUR450C, AUR350C, and RX series 
       are supported.
       Manufacturer name and series name are changed.
     - Fuji Electric Co., Ltd. MICREX-SX series SIO
       General Interface Capsule FFK120 A-C10 is supported.
     - GE Intelligent Platforms Series 90 Ethernet
       The maximum number of the connection unit is changed from "16" to "32".
     - LSIS Co., Ltd. XGT/XGB series Cnet
       XGB series is supported.
       Series name is changed.
     - Modbus-IDA General MODBUS SIO Master
       ASCII mode is supported.
       Driver's series name is changed.
     - Siemens AG SIMATIC S7 Ethernet
       The tag import function is supported.

(2) Limitations
 2-1 Editor
  (Editor)
  <Error Check>
   - When working with a LT4000 series project with an Italian,
     Chinese(Simplified) or Korean interface, an error may appear
     during Error Check even though there are no errors in the project.
  <Workspace>
   - The Parts Toolbox and Shape Browser may incorrectly list 65,535 colors
     instead of 65,536 colors.
   - In the Address workspace, double-clicking the [Feature], [Location],
     or [Screen] column may revert the list to its default sort settings.
  <Logic Monitor>
   - When running Online Monitor on a network,
     the connection may fail and show the error "Code=2".
  <Transfer Tool>
   - When running [Compare Project], some of the differences identified
     in the [Text Table] settings may show unrelated [Exclusive Screen]
     differences.
   - After operated the [Reduce Images to 16-Bit Colors] to the Image parts
     which are [Reduce Colors] setting is 16,777,216 Colors, 
     you operate [Transfer Project] and then the error message may be shown.
  <Project Converter>
   - There may be cases when you cannot convert sampling groups assigned
     to a historical trend graph that is grouped.
  <Enhanced Recipe>
   - Do not operate the [Undo] or the [Redo], when you sort by each items
     in the element list - [Recipe Group].

 2-2 Display Unit
  (Runtime)
  <USB Device>
   - When a USB device is inserted/removed, all USB devices may not become 
     disabled under the condition that five or more USB devices are connected 
     at the same time using the USB HUB in GP-4000 series. 
     If this phenomenon occurs, reset the Display.
  <Data Display>
   - When two or more Data Displays with "Indirect" specified are made to be 
     invisible at the same time while displaying a pop-up keypad, some Data 
     Display may not be invisible.
  <RPA>
   - A keypad is closed while the [Alt] key on the keypad of the RPA 
     Window Display is held down. When the keypad is opened next time, 
     the [Alt] key remains held down.
  <USB/SIO>
   - Do not use a logic program during communication with a Device/PLC using 
     a USB/SIO (RS422/485).
     If the logic program is used in the situation, a communication error 
     may occur.
  <Logic Program>
   - In GP4000 series (except for GP-4100 series) and LT4000 series, the buzzer 
     sound in Ver. 3.5 is different from that in Ver. lower than 3.5.
  <EZ Fingerprint Recognition Unit>
   - Do not attach/detach the fingerprint authentication unit while turning on
     the power to the Display. Doing so, inconsistency occurs between the
     security data and the fingerprint data and the display of the
     authentication and the password setting may not operate normally. 
     If an inconsistency occurs between them due to attachment/detachment of the
     fingerprint authentication unit, update the  fingerprint data of the
     fingerprint authentication unit using the "Update DB" function.

 2-3 Device/PLC
  <Fuji Electric Co., Ltd. MICREX-SX Series SIO>
   - Do not use "Indirect" setting for the String type. If it is specified, 
     data may not be displayed normally.
   - When STRING variables are displayed in Device Monitor of Pro-Server EX, 
     only two characters are displayed.
  <GE Fanuc Automation Series 90-30/70 SNP>
   - Some spelling mistakes are found in English error messages.
  <GE Fanuc Automation Series 90-30/70 SNP-X>
   - If an error occurs during communication, set "1" or larger value 
     for Retry Count.
  <Mitsubishi Heavy Industries, Ltd MHI STEP3 Ethernet>
   - When a bit device is specified in Alarm Summary, alarms of 17th bit or 
     later are not displayed normally. If this phenomenon occurs, use the word 
     device.
  <Mitsubishi Electric Corporation FREQROL Inverter>
   - When the link parameter device is read, the communication cycle time 
     becomes an illegal value.
  <Mitsubishi Electric Corporation Q Series CPU Direct Connection>
   - In a screen where a Display Unit does not communicate with a PLC:
     When an access is made to the PLC using the pass-through function 
     after the PLC is restarted, the password lock occurs to the PLC.
     Make connections using the pass-through function after the screen is 
     shifted to the one where the Display Unit communicates with the PLC.
   - Do not write the data including the bit address with the extended recipe 
     function. If such writing is made, a communication error may occur.
  <ODVA DeviceNet Slave>
   - Do not input 32 or more characters for the device address in Address Input 
     of Device Monitor.
  <Rockwell Automation EtherNet/IP>
   - Tag information allocated to I/O units may not be imported normally.
     If this phenomenon occurs, edit the data with the Editor manually.
  <Siemens AG>
  <PROFIBUS International>
   - When bit read/write for two or more points is performed to 
     a bit-accessible word device or word type tag, an address other than 
     the specified address may be read/written.
  <Pass-through Function>
   - The pass-though function cannot be used when WinGP and IIS FTP servers are 
     used at the same time.

 2-4 WinGP
  <Function>
   - The buzzer of WinGP does not sound in PS-4700 (Z510).
  <File Manager>
   - When the File Manager displays a folder path and data in that folder is
     updated, the folder path reverts to the default path.

(3) When Serial No. and License Key Code are not input
   - Project data cannot be transferred to the operation panels
     (except for GP4100 series, IPCs and PC-ATs (Used WinGP)).
   - Transfer using the Transfer Tool is not available for WinGP. However, using
     ProjectCopy, you can copy screen data and get it to work.
     To use ProjectCopy, click [Start]-[All Programs]-[Pro-face]-[WinGP]-
     [ProjectCopy] on the Windows desktop screen.
     However, note that ProjectCopy cannot be used in the following cases:
     - When system data has not been transferred
     - When system data has been changed
       WinGP automatically stops after three hours of continuous operation.
      * It is possible to input the serial No. and the license key code after
        installation of the software. Start the product and go to [Help]-[Enter
        Key Code].

(4) Installation and Uninstallation
 4-1 Installation
   - Be sure to quit all application programs and close (disable) all resident
     programs such as virus detection software before installing the software.
   - Install this software using a user account with Administrator privileges.
   - Refer to our support site "Otasuke Pro!" (http://www.proface.com/otasuke/)
     for the operating environment.
   - By inserting a disk into the DVD drive, Setup window will appear.
     If the Setup window does not appear, click the desktop's [Start] button
     and then click [Run]. In the text input field, enter [D:\ProEX_Setup.exe]
     and click [OK].
     (As for the "D:\" part, enter your DVD drive name.)
       * Some of the tools require a license.
       In cases below, USB transfer cables may not be recognized correctly:
       - When you installed the software with a USB transfer cable connected
       - When you started using the software without restarting your computer
   - <How to install ".NET Framework2.0" when not connected to Internet>
     1)Insert the DVD media of Windows 8 into the DVD drive. 
       If there is no DVD media of Windows 8 found, contact the PC
       manufacturer.
     2)Select "Open command prompt as administrator" on the Explorer.
     3)Execute the following command at the Command Prompt.
       Dism /online /enable-feature /featurename:NetFx3 /All /Source:x:\sources
       \sxs /LimitAccess 
       *) For x:, specify the drive letter of Windows 8 Install Media or the DVD
          drive.

 4-2 Uninstallation
   To uninstall the software, click on [Start], then select [All Programs]-
   [Pro-face]-[***], and execute [Uninstall]. ("***" represents the product
   name and version.) Project files and files in your package files will not be
   removed by this operation. Delete other tools from [Start]-[Control Panel]-
   [Add or Remove Programs].

(5) User Registration
   Please register your software to help us offer enhanced customer support.
   Since you can confirm the registered information at anytime once you
   register, you do not have to worry even if you lose it. To register, insert
   a DVD into the DVD drive, select the User Registration menu in the Set Up
   Menu screen and complete the online Software User Registration. You can also
   register after installation by starting the product and registering from
   [Help]-[Online User Registration].

(6) Manuals
   To view PDF manuals, the Adobe Reader software must be installed on your
   computer. Start the product and select [Manual] from the [Help(H)] menu.
   To view only the manuals, select [Start]-[All Programs]-[Pro-face]-[***]
   -[Manual].("***" represents the product name and version.)
   Some manuals need to be downloaded from our support site "Otasuke Pro!".

(7) Fixed Defects
= V3.60.000 ===================================================================
 7-1 Editor
  (Editor)
  <Error Check>
   - An error of size shortage in the address is occasionally displayed,
     although the size of the address is not insufficient.
   - In the Device/PLC from Simens AG, PROFIBUS International, and
     Fuji Electronics:
     Reading/Writing of the bits at two or more points cannot be detected as an
     error in the word type tag or the word device in which bit access can be
     made.
   - An error cannot be detected in a Display in which a file copy function of
     the Expansion Script and the FTP function cannot be used.
  <Switch Lamp>
   - In the case "Do Not Synchronize Labels" is specified for "Label Resizing":
     When a part size is changed in the Properties window, the label size is
     changed.
  <Fingerprint Authentication Setting Tool>
   - A dialog is not correctly displayed when displayed in the simplified
     Chinese.
  <Simulation>
   - Values between the screen and the address view may not be matched in a
     part having 32-bit data format where the symbol variable array is set.
  <Display Unit>
   - When the series is changed with the same connection device, the address in
     "System Area Start Address" is returned to the initial value.
  <I/O driver>
   - When the EXM module is used in  LT3000 series, a variable allocated in the
     channel is changed to a not-yet allocated state.
  <Transfer Tool>
   - Automatic transfer cannot be executed when the following settings are made:
     "9990" or larger is set for the port setting in "Ethernet Setting" which is
     in the off-line screen of the Display. "Variable Value" is unchecked in the
     transfer tool setting. LAN transfer is specified.
   - When System Transfer and Project Transfer of the project file (V3.10.0 or
     higher) are executed to GP-4201TM and GP-4301TM (sub-system version: lower
     than V3.10.0) and then the project is received, the received project file
     cannot be opened with the screen editor.
   - When "Automatic" is specified for System Transfer and the version of the
     system is upgraded in the LT4000 series, a part of the text on the offline
     screen is not displayed.
   - Project transfer cannot be completed normally when a project file (having
     the function where SD card is used with the Display which does not support
     an SD card) is transferred.
  <Logic Monitor>
   - GP-ProEX is terminated with an error when a user performs an online edit of
     a function block in the logic program and then tries to make the setting of
     the edited function block.
   - The Display hangs up when the setting values of the timer instruction and
     the counter instruction are changed in Online Monitor of the logic program.
  <Version Reverter>
   - A project file which is in the state where parts are locked in Special Data
     Display (CSV display) or Sampling Data Display cannot be converted with
     Version Reverter.
  <Properties>
   - In "Key", "Switch Lamp", and "Text" in which "Text Table" is specified for
     "Text Type", the input candidate pop-up of "Text" that exists in the
     Properties window is not displayed.
  <Utility>
   - A file cannot be saved normally when "Copy from Another Project" is
     executed to the project where symbol variables are specified in Logic from
     the project where the logic address is specified in Logic.

 7-2 Display Unit
  <Screen Transfer>
   - When screen transfer is interrupted by turning off the power and screen
     transfer is required in the next forced transfer screen in GP-4201TW,
     screen transfer cannot be executed using the USB transfer cable
     (CA3-USBCB-01).
   - Reset occurs to the Display even when reset is not required, when Auto
     Transfer is executed in the Modular Type of the LT-4000 series.
  <EZ Fingerprint Authentication Unit>
   - When touch operation is performed while updating the database, operation is
     delayed after the update is completed. This bug has been corrected so that
     touch operation cannot be operated during update.
  <MODBUS TCP Communication>
   - Modbus TCP communication error in GP-4000 series (except for GP-4100
     series, GP-4201TM, and GP-4301TM) and LT-4000 series
  <Off-line>
   - When the project data whose setting is changed in the off-line mode is
     compared by using the project comparison tool, differences are found
     although their settings are quite the same.
  <Sampling>
   - Hang-up occurs when a lot of words and group numbers are specified for
     Modular Type in GP-4000 series and Modular Type in LT-4000 series.
  <SD card>
   - Writing with an SD card fails in GP-4000 series (Except for GP-4100 series,
     GP-4201TM, and GP-4301TM)
  <Filing>
   - SRAM transfer of the filing data occasionally fails in the Modular Type
     (lower than V3.00) of GP-4100 series and GP-4000 series.
   - The filing parts do not operate normally when the filing parts having the
     same identification number as the filing parts being displayed in the
     Display are displayed in asynchronous connection from the Pro-face Remote
     HMI.
  <Alarm Banner>
   - The Display may hang up in extremely rare cases when the print operation of
     any function is started during alarm banner display.
  <Screen Display>
   - In LT-4000 series and GP-4000 series (Except for GP-4100 series, GP-4201TM,
     and GP-4301TM): 
     When MPI communication is used, update of the screen is stopped for a few
     seconds.
  <Print>
   - When print is not performed normally in Alarm History (batch print),
     Sampling (block unit print), and CSV Display using the stroke font.
  <CSV Display>
   - In the state where a CSV Display is displayed on a screen:
     When a CSV Display on another screen is displayed from Pro-face Remote HMI
     in the asynchronous connection,  the CSV Display does not operate normally.
  <Others>
   - GP4000 series (except for GP4100 series, GP-4201TM, and GP-4301TM) and
     LT4000 series:
     If the IP address was duplicated with other equipment, IP address would not
     display correctly.

 7-3 Device/PLC
  <Fuji Electric Co., Ltd. MICREX-SX-series SIO>
  <Fuji Electric Co., Ltd. MICREX-SX Series Ethernet>
   - Variable data cannot be imported normally 
     when D300win V3.6.1.3 or later is used.
  <Shinko Technos Co., Ltd Controller SIO>
   - When the external device is changed 
     while two or more communication driversare set with GP-Pro EX, 
     an application error may occur.
  <OMRON CS/CJ/NJ-series EtherNet/IP>
   - After transfer to NJ Series from a ladder tool 
     is executed during connection with the NJ Series, 
     communication becomes disabled. 
  <PROFIBUS International>
  <ODVA DeviceNet slave>
   - GP hangs up 
     when shifting to the off-line without installing the expansion unit 
     with the GP3000 series. 
  <OMRON CS/CJ series Ethernet>
  <Yaskawa Electric Corporation MP/Inverter/Servo Ethernet>
  <YOKOGAWA Electric Corporation Personal Computer Link Ethernet>
   - "Send Wait" does not operate as it has been set in the UDP communication.
  <OMRON CS/CJ/NJ-series EtherNet/IP>
   - When resetting the Display, 
     turning on/off the power or project transfer is repeated, 
     communication may be disabled. 
  <Mitsubishi Electric Corporation A series Computer Link>
  <Mitsubishi Electric Corporation  FX series  Computer Link>
  <Mitsubishi Electric Corporation) Q/QnA Serial Communication>
  <OMRON C/CV series Host Link>
  <OMRON CS/CJ series Host Link>
  <Yokogawa Personal Computer Link SIO>
   - When GP430 series and GP4000 series are mixed in the serial multilink, 
     all GPs cannot make communications.
  <Rockwell Automation EtherNet/IP>
   - The project data created with a past version cannot be opened correctly. 

 7-4 WinGP
  <Off-line>
   - When the setting is saved in the off-line mode with WinGP, the writing
     error of the key code is displayed.
  <Function>
   - In WinGP (V3.00 or later), the speed of the screen change from the screen
     where many parts having the animation function used are placed is very
     slow.

= V3.50.000 ===================================================================
 7-1 Editor
  (Editor)
  <Switch/Lamp>
   - An alarm message indicating that a touch warning sound doesn't operate is 
     not displayed on the Display which does not support the Interlock-Touch 
     Warning Sound function.
   - An error is not detected during error check, although "Security" in 
     "Special Action" is not supported.
  <Alarm>
   - When alarms are registered exceeding the specified registration limitation 
     and then error check is performed, the alarm registration number error and 
     a setting error for a normal IO driver may be detected.
  <Data Display>
   - "Transparent" may not be specified for "Plate Color" in "Color/Alarm".
  <Function Block>
   - Even when #H system variables are used in the function block exceeding 
     the number of limitation, an error may not be displayed.
   - An IEC address may be displayed in the local variable in the function 
     block.
   - The local variable in the function block may be determined as an error 
     during the error check, although it is correct.
   - Attempting to re-edit a variable within the function block in Online  
     Editing may cause an abnormal termination.
  <Project Information>
   - In the "Number of Addresses Used in Logic" dialog:
     Even when the address points used exceed the specified limit value, 
     the progress bar may not be displayed in red which indicates an alarm.
  <Function>
   - An alarm message is improved which is output when a project is read 
     using a Device/PLC whose version is lower than that of the Device/PLC 
     when the project has been created.
  <Address Conversion>
   - An abnormal termination may occur when a symbol array name is specified to 
     the converted address.
  <Work Space> 
   - When a symbol array is specified to the parts:
     An address different from an address to be accessed in Simulation may be 
     displayed in Screen Data List work space.
  <Simulation>
   - When a symbol array is specified for Monitor Word Address in 
     Numeric Display, values between the parts and the address view may be 
     different.
  <Transfer Tool>
   - In the transfer tool where the display language is English:
     When backup data including an I/O driver is checked, the I/O driver name 
     may not be displayed correctly.
   - A correct Runtime version may not be displayed in the transfer file 
     information.
  <EZ Fingerprint Recognition Setting Tool>
   - Cancellation may not be performed during fingerprint registration, 
     even when the Cancel button is pressed.

 7-2 Display Unit
  (Runtime)
  <System Keypad>
  - A spelling mistake is found in the User ID and Password Input window 
    when the display unit orientation is "Portrait".
  <Picture Display>
   - For the Picture Display, when a screen containing a part with "Mark" 
     specified and other part (e.g. text) is called and moved for display, 
     the display position of the part other than the Marked part becomes 
     incorrect.
  <Sampling>
   - In GP4000 series (except for GP-4100 series), LT4000 series, and WinGP:
     When "Text" is specified for "Data Type" in the Sampling screen, 
     the text "00" cannot be displayed or saved.
   - In GP4000 series (except for GP-4100 series), LT4000 series, and WinGP:
     When "Text" is specified for "Data Type" in the Sampling screen, 
     a part of the two-byte character may be missed during sampling.
  <Data Display>
   - In LT3000 series and GP3300 series (Less than Rev.*-4):
     A pop-up keypad may not be undisplayed when inputting in the Data Display 
     screen.
  <Enhanced Recipe>
   - A part of character strings registered in the enhanced recipe may not be 
     written in the Device/PLC.
  <Logic Program>
   - An error may be displayed when resetting a logic in LT4000 series.
  <Security>
   - When "Change-To Screen" of LS8 is changed while the log-in screen is 
     displayed in Security Settings, the screen may not be changed normally.
   - When the password settings are exported from the Editor, the Display 
     cannot import the security data.
   - In GP4000 series (except for GP-4100 series), LT4000 series, and WinGP,
     the Display may hang up when an error occurs in password input of the
     Security function.
  <Simulation>
   - The brightness bar is displayed during simulation.
  <Pro-face Remote HMI>
   - While the communication state between a client and a server is unstable, 
     reconnection may be frequently generated.
  <Others>
   - In GP4000 series (except for GP-4100 series, GP-4201TM, and GP-4301TM), 
     and LT4000 series:
     A communication error is generated when connecting/disconnecting the LAN 
     cable in UDP communication, and the error may not be restored.
   - In GP4000 series (except for GP-4100 series, GP-4201TM, and GP-4301TM):
     When reset is executed, 5V may be momentarily output from 9-Pin of 
     the COM1 port.

 7-3 WinGP
  <Function>
   - In the case of PS4000 series with Windows7 64bit version, WinGP of a trial 
     version is started even when a correct key code is entered.
   - The message saying "Could not save a key code because access was refused." 
     may be displayed.
   - Hung-up may occur when a fingerprint recognition unit is 
     connected/disconnected.

 7-4 Device/PLC
  <Beckhoff Automation GmbH TwinCAT ADS/AMS>
   - Bit Write operation does not work normally for BOOL arrays or 
     BYTE/SINT/USINT arrays.
  <GE Intelligent Platforms Series 90 Ethernet>
   - When screen change is repeated, data read from the PLC may not be updated.
  <LS Industrial Systems XGT/XGB Series FEnet>
   - Continuous Bit devices (P, M, K, and L) cannot be correctly written.
  <Mitsubishi Electric Corporation Q Series QnU CPU Ethernet>
   - Communication with an external device may be stopped temporarily and 
     restarted.
   - An error may occur when data is written to random bit addresses of 
     a motion CPU at one time with Pro-Server EX.
  <Mitsubishi Electric Corporation Q/QnA Series Ethernet>
   - Communication with an external device may be stopped temporarily and 
     restarted.
  <Panasonic Industrial Devices SUNX Co., Ltd. FP Series Computer Link SIO>
   - An application error may occur when "Change Device/PLC" is executed from 
     some of the communication drivers.
  <Rockwell Automation EtherNet/IP>
   - When a project created with a driver (Ver. 1.11.04 or earlier) is used, 
     the address may be inappropriate or "Undefined".
   - Module definition in which a controller tag and data type/structure are to 
     be created may not be imported normally.

 = V3.12.000 ===================================================================
 7-1 Editor
  (Editor)
  <Text Table>
   - When you try to paste a text on Table 2 or later under the condition that 
     other language than English Standard Font, English Stroke Font and Russian 
     (Cyrillic) is specified for Table 1, the paste operation cannot be 
     performed normally.
  <Switch/Lamp>
   - When the setting dialog is opened under the condition that only Lamp is 
     set, the IME input mode may be cancelled.
  <Logic Instructions>
   - Setting values in Timer instructions, Timebase, and setting values in 
     Counter instructions when "Address Format" is specified cannot be saved 
     normally.
  <Print>
   - Properties of Print cannot be displayed in Windows7 (64-bit version). 
  <Transfer Tool>
   - When a user does not update a project file but tries to upgrade the 
     version of the communication driver only under the condition that 
     "Automatic" is specified for Transfer System" and "Transfer Project", 
     the version of the communication driver may not be updated.
  <Data Display>
   - When "Extended" is selected in "Color/Alarm" of "Numeric Display", 
     the plate color cannot be set to transparent. 

 7-2 Display Unit
  (Runtime)
  <Data Display>
   - It may take time to execute Screen Change in V3.10.000 when changing 
     from a screen in which many Data Displays with "Allow Input" specified 
     are placed.
  <System Keypad>
   - A password entry screen is not displayed normally when "Large" is 
     specified for "System keypad size."
  <Others>
   - FlashBIOS of some models is improved in GP-3300 series and LT3000 series.

 7-3 Device/PLC 
  <OMRON Corporation C/CV Series HOST Link>
   - GP cannot write data to TIM/CNT device of C series.
  <OMRON Corporation CS/CJ/NJ Series EtherNet/IP> 
   - GP cannot access a BOOL type tag when I/O is allocated to the BOOL type 
     tag of NJ series.
   - The Display may hang up if PLC has a BOOL type tag in the member of 
     structure at NJ series when using driver version V1.15.02.

 = V3.10.000 ===================================================================
 7-1 Editor
  (Editor)
  <Function>
   - Some key labels are shifted and displayed among keypad parts registered in 
     the package.
   - When a project is opened, the standard font may be displayed 
     in a different size from a preset size.
   - When Prx is converted, the plate color of Message Display may be set 
     to "Transparent".
  <Transfer>
   - System Keypad becomes small in memory loader backup data of GP-3310T.
  <Alarm>
   - When the display language is different between OS and the screen editor, 
     a part of the alarm part settings may not be displayed normally.
   - In the Switch setting of the Alarm part, the label of "Clear All" may not 
     be changed.
  <Text Table>
   - When a table having no language information exists in a CSV file to be 
     imported with Text Table, a project cannot be opened normally after the 
     import.
  <Switch/Lamp>
   - When a specific operation is made in the "Add Text" dialog 
     under the condition that "Text Table" is selected in the Label setting, 
     abnormal termination may occur.
   - When "Copy Part Shape" and "Paste Part Shape" are executed, the Color item 
     in the part settings may disappear.
  <Special Display>
   - When a language of the European language package is selected, 
     the input area of Default Path of the Extended tab in File Manager cannot 
     be selected by clicking.
  <Enhanced Recipe>
   - When "German" is selected in the language setting of the screen editor, 
     the words and phrases in "Enhanced Recipe" are not uniform.
  <Transfer Tool>
   - Recipe files (CSV file) cannot be compared with the Compare Project 
     function.
   - When a screen data (MEM file) which is image-font-registered is converted 
     in a project (PRX file), the project data may not be opened normally.
  <Script>
   - When specific operation is made in the edit screen of Script, 
     the screen editor may be terminated abnormally.
   - When a project including the script where an address (in which a data type 
     is individually specified) is described is opened with the screen editor 
     of V3.00 or later, the address may be converted in an illegal address.
   - The "Undo" operation may not be operated normally.
   - The alarm message displayed when a value exceeds the 32-bit range of the 
     value is incorrect. Instead of the correct one, the alarm message 
     displayed when a value exceeds the 16-bit range is displayed.
  <Data Display>
   - When the installation direction of the Display is changed, 
     the arrangement location specification of the keypad may be shifted.
  <Memory Loader>
   - Backup data created from a project where the font whose size exceeds 
     the font area is used cannot be downloaded normally.
  <Operation Log>
   - When "English" is specified in the language setting of the screen editor, 
     "Sec" is not displayed in "Time" of "CSV Format."
     ("Operating Log => Settings"CSV Format")
  <Project Converter>
   - Address conversion for the LS device which is not described with 
     a 4-digit address and 2-digit bit may not be executed normally.

 7-2 Display Unit
  (Runtime)
  <FEP>
   - When one window is cancelled while an FEP input window is displayed, 
     the FEP input window is closed as well. In addition, when "SD/USB Removal" 
     is enabled, the FEP input window may be closed in a few seconds.
  <Alarm>
   - When scanning is stopped using LS9550 (Communication ON/OFF control)
     under the condition that "Extended" is selected for "Alarm Type", an alarm 
     for which the trigger conditions are not met may be generated.
  <Image Registration>
   - When "Monochrome" is specified in the conversion processing at the time of 
     registering image files, the converted image may not be displayed normally.
  <Offline>
   - Hung-up may occur when the System Area setting is selected in offline mode 
     for the following project:
     - In the project, a system area start address is specified on an address 
       input keypad where "Indirect" is specified for "Address Mode."
   - For GP-4000 series (except for GP-4201TW, GP-4301TW, GP-4401WW, and 
     GP-4501TW) and WinGP:
     When SRAM backup data in the SD card is transferred to the Display, 
     the internal device backup data may not be updated.
   - For GP-4201TW, GP-4301TW, and GP-4501TW:
     SRAM backup data in the SD card cannot be transferred to the backup memory 
     (SRAM) of the Display.
   - When printer settings are changed, the changed settings are not saved 
     normally.
  <Screen Capture>
   - The file number of the JPEG capture may not be increased 
     when opening/closing the CF card hatch in GP3000 series.
  <Simulation>
   - When there are a lot of data numbers in the recipe settings, 
     the simulation function does not start in rare cases.
  <Script>
   - A file copy function _ FileCopy of Extended Script in GP4000 series does 
     not read a CF of the root folder as an SD.
  <Data Display>
   - For some display types in which the upper limit of the parts for one 
     screen is 1024:
     When 385 or more Data Displays whose input is permitted exist, 
     input is disabled from Data Display.
  <Drawing>
   - When Screen Change is executed in WinGP or Simulation, 
     a drawing of the previous screen may remain in rare cases.
  <Function Key>
   - The bit allocated to the switch does not turn OFF when Device/PLC is 
     changed (Indirect Device) and transition to an offline mode with holding 
     down the global function key under the condition that the global function 
     key is specified and the bit momentary switch is allocated.
  <Memory Loader>
   - When a screen is scrolled on the Memory Loader's "Select File" screen or 
     "File List" screen, the folder cannot be moved to a lower folder.
  <Monochrome>
   - When a monochrome 16-level 3-speed blink is used in GP4000 series, 
     a 1-line error, FEP, and detailed error window may be reverse-displayed.
  <Logic Monitor>
   - When a logic monitor is scrolled in AGP-3750, a straight line of a few 
     dots may remain as they are, instead of disappearing.
  <FlexNetwork>
   - When the power of the I/O module is turned OFF/ON, communication may not 
     be restored.
  <File Manager>
   - In GP-4000 series (except for GP-4100 series, GP-4201TM, and GP-4301TM):
     When 99 or more files and folders are stored in the folder in the SD card, 
     the files and folders cannot be deleted with File Manager.
  <Historical Trend Graph>
   - When GP-4000 series (except for GP-4100 series, GP-4201TM, and GP-4301TM) 
     is used in the portrait orientation and the past data is displayed in 
     Historical Trend Graph, a graph may not be displayed normally.
  <Ethernet>
   - In GP-4000 series (except for GP-4100 series, GP-4201TM, and GP-4301TM):
     When Ethernet connection is made with peripherals with the IP address set 
     to 10. ** . ** (** indicates an arbitrary number), an ARP command may be 
     issued to the IP addresses of 10.1.2.40 and 10.1.2.90.
  <Standby Mode>
   - In GP4000 series (except for GP-4100 series): 
     It is necessary to touch a screen twice to display the screen again 
     when screen display is turned OFF using an address of "Screen Display ON/
     OFF" in the system data area after the mode is shifted to the standby mode.

 7-3 Device/PLC
  <Azbil Corporation Controller (CPL)>
   - When a controller is specified in Pro-Server EX, 
     a part of the Reference To Parameter dialog may be hidden.
   - The Reference To Parameter dialog is not displayed normally when "120 
     DPI" is specified for DPI.
   - Communication performance has been improved by eliminating useless idle 
     time in the communication with Device/PLC.
  <Cognex Corporation In-Sight Vision System>
   - For GP-4000 series (except for GP-4100 series, GP-4201TM, and GP-4301TM):
     LIVE image may not be restarted after it is stopped.
  <Digital Electronics Corporation General Purpose Ethernet>
   - The error message and error status are not displayed normally 
     when a communication error occurs.
   - Incorrect error codes are set in "Sending Result" in some errors.
  <Fuji Electric Co., Ltd. MICREX-SX Series SIO>
   - When variable data is newly created, the data may be created with the 
     existing variable data name.
   - When the task type is "FIXED_CYCLE" only, a communication error occurs and 
     communication is disabled.
   - In ProServerEX, display and operation may be illegal 
     in the node's Device/PLC settings.
   - Although Read/Write is executed to 32-bit variables, 
     Read/Write is performed for every 16-bit.
  <IAI Corporation ROBO CYLINDER MODBUS SIO>
   - When a lot of discontinuous addresses are used, a communication error may 
     occur.
  <LSIS Co., Ltd. MASTER-K Series Cnet>
   - When a lot of discontinuous addresses are used, a communication error may 
     occur.
  <Mitsubishi Electric Corporation FX Series CPU Direct Connection>
   - When the communication type settings for GP4201T and GP4301TM are 
     different from those of the connected devices and further the time 
     synchronization setting is specified, the screen may be locked 
     during the startup.
  <OMRON Corporation CS/CJ/NJ Series EtherNet/IP>
   - When the Byte array of the NJ series is used at random, a correct value 
     may not be displayed.
   - When 83 or more variables of a short character string are continuously 
     registered in the NJ series, an error occurs when communication is started 
     and communication cannot be started normally.
   - When a lot of variables of a long character string are continuously 
     registered in the CJ2 series, an error occurs when communication is 
     started and communication cannot be started normally.
     (Example)
     39 or more variables with 48 characters are continuously registered.
  <Rockwell Automation EtherNet/IP>
   - Array Tag cannot be specified normally.
   - For saving a tag list as a file with the export function:
     When a file name with read-only properties is specified for a file name, 
     abnormal termination occurs.
   - A Japanese error message when Ethernet/IP L5K import is executed is not 
     correct.
   - When L5K is imported, an error occurs to a tag which should have been 
     imported normally and one character is missing for the data type of the 
     error log to be output.
  <Schneider Electric SA MODBUS Slave>
   - When a REST packet is transmitted from a partner device 
     during TCP communication, an internal memory may be accessed illegally.
  <SHINKO TECHNOS CO., LTD Temperature Controller SIO>
   - Communication performance has been improved by eliminating useless idle 
     time in the communication with Device/PLC.
  <Siemens AG SIMATIC S7 Ethernet>
   - The out-of-range check before transmitting a command in the continuous bit 
     address access is not correctly made.
  <Siemens AG SIMATIC S7 MPI Direct Connection>
   - A communication error occurs when the tag (Array Element Number: 213 or 
     more, Text format) is accessed.
   - When screen data including a text format tag which is created with 
     GP-ProEX V3.00 is displayed, the screen may be locked.
   - When 8 or more tag data is created in the tag list selection screen, 
     specification of the 9th or later tag file causes an error.
   - When 110 points or more continuous timer/counter type tags are read, 
     the 110 or later data is not read normally.
   - When the timer/counter type tag is specified in S7-200 series, a correct 
     value is not read.
   - Performance when the timer/counter type tag is specified in S7-200 series 
     is improved.
   - RHAA101 or RHAA049 error occurs when project data in which 16 files or 
     more tag data is created is used to make communications.
   - 110 points or more tags including the Date_and_time type tag are read 
     continuously, the value may not be read correctly.
   - When an array format tag of the 2-word data is 110th word in continuous 
     reading of the array format tag, the correct value cannot be read.
   - When a TOD-type tag is specified for the start condition detailed settings 
     in Pro-Server EX, a correct operation is not performed.
  <Siemens Building Technologies SAPHIR SIO>
   - When one data point is deleted in the case two data points can be 
     registered doubly, an application error occurs in GP-Pro EX.
  <TOSHIBA MACHINE CO., LTD. TC series (TCmini/TC200)>
   - When you try to make a communication using GP3000 series COM1 (2-wire), 
     a cable disconnection error occurs, which disables communication.
  <YASKAWA ELECTRIC CORPORATION High-speed Ethernet Server>
   - When robot information is backed up all at once in GP4000 series, 
     the 2nd backup is not performed normally.
   - Port settings in Individual Device Settings are not correctly reflected.
   - When a class is specified in Address Input dialog, other setting ranges 
     are not set normally.
   - File Read <job program> does not operate normally in Handy GP.
   - When a file read class (0x4C0) is used and a file is created in the root 
     folder of the SD card in GP4000 series, the file is not overwritten with 
     the same file name and the error occurs.
  <Device Monitor Function>
   - The Device/PLC name on the title bar is not displayed normally when it is 
     long.
   - When you try to start the Device Monitor function at high-speed 
     continuously, the Display may be locked or the Device Monitor function may 
     not start normally.
  <Pass-through>
   - Communication may not start when GP is started.

 7-4 WinGP
  <Function>
   - The resolution of the desktop may not be returned to the original one 
     when WinGP is terminated after WinGP is used in the full-screen mode with 
     Windows7.
   - When "Screen Display" of the not-supported System Area is turned OFF 
     in WinGP, the setting of "Faded Color Blink" may be changed to "Black" 
     from "Faded Color". In this case, touch input may be disabled.

================================================================================
Copyright (C) 2014 Digital Electronics Corporation. All Rights Reserved.
"The Terms and Conditions of Software License Agreement" of Digital Electronics
Corporation do not apply to Adobe Systems products.
All product names in this document are registered trademarks or trademarks of
their respective owners.
Pro-face is a registered trademark of Digital Electronics Corporation in Japan,
U.S.A., Canada, Europe and other areas and countries.
No part of this document may be used or reproduced without permission.
****************************  End of Release Note  *****************************